Category: knits

Customizable Baby Suspenders!

My very first knitting pattern! It’s more of a “recipe” than a pattern, however. A friend asked for some knit baby suspenders, so I did a little research, and came up with a plan.

These are SUPER simple and fast to knit. Use whatever scrap yarn you have lying around the house and whatever needles you have that are an appropriate size for your yarn.

These suspenders aren’t intended to actually hold up pants. They are intended to be adorable!

  • Cast on enough stitches to make the suspenders about 1 inch wide.
  • Knit whatever stitch you want! (I used Garter stitch on the yellow pair, and Linen stitch on the multicolored pair)
  • Keep knitting until you have the length you want (Use the Suspenders Size Guide for reference, and keep in mind that knit suspenders will be VERY stretchy).
  • Bind off, knit another just like the first!
  • (Optional) cross and sew your suspenders together in the back.
  • Attach suspender fasteners (I used the Fashion Fit Clips suggested by Ashley’s Little Boy Suspenders craft post) with snap buttons, regular buttons, or just sew them on!
  • Add any embellishments you want!

Feel free to leave comments! I want to see how you customize your baby suspenders!

Download the pattern here or on Ravelry!

CustomizableBabySuspenders

Custom Earring Holder

I had an old frame lying around the house. It was missing glass and any hardware, and I’d painted it and put it in various places around my house. So I made an earring holder!

IMG_5280-764x1024I used Size 7 needles, Crochet thread, and a 5-pattern-repeat of the Dainty Chevron pattern, found on KnittingFool.com.

I knit until it was about as long as the frame opening, then I bound off and attached the lace to the frame via staple gun. A helpful hint – staple gun the center of each side, then work around equally – that way you don’t end up with your lace cockeyed inside your frame.

You could use any lace pattern, and size frame, and any size yarn! Definitely do a gauge check so you don’t end up with a lace piece way too big or too small for your frame. (Too big wouldn’t be as bad as too small, though.)

Customized Knitting Needles!

The other day I realized that I’ve been knitting for almost 7 years! I had this realization while trying to find the twin to my US7 straight bamboo needle, and being frustrated with the lack of organization in the 7-years worth of knitting needles I’ve collected. And why are the sizes engraved with tiny little numbers on the side of the needle, where they’ll eventually wear off with use?

Suddenly inspiration struck. I should label my needles on the top, and add a bit of color while I’m at it!

Here are the steps to make your own customized knitting needles!

  • Step 1: Set up your work space. I placed a scrap piece of cardboard on top of 2 sawhorses so that I could stick my needles through the cardboard, keeping them secure, making them easier to paint, and giving them a safe place to dry. I also used a pegboard to keep things organized, but that’s not at all required.
  • Step 2: Arrange your needles by their size, and stick them through the cardboard. I used the screwdriver to poke the holes for the skinnier needles, since I was worried I might break them while trying to jab them through the cardboard.
  • Step 3: Paint! I used acrylic paint and a basic old paintbrush. (Because I’m a color nerd, I found a color palette I liked from colourlovers, saved it on my phone, and used it to pick out my paints.) I painted 3 coats total, because I wanted to make sure I had excellent coverage. Acrylic paint dries SUPER fast, so 3 coats of paint was easy to do. I found the easiest strategy was to spin the needle from under the cardboard, and brush from bottom to top of the needle “bead” until all sides were painted, then finished with a brush or two on the top.
  • Step 4: Once your paint is dry, use a sharpie to write the needle sizes on the top. I also thought of using a sticker or a stencil, but at this point I just wanted to finish them, so I just used the sharpie.
  • Step Oops! (Not Suggested) Accidentally grab a can of black spray paint instead of the clear coat, and spray black speckles all over your beautiful needles. Immediately stop and freak out. Curse at things. Take a break and grab a beer. Inspect the damage. Decide your needles aren’t ruined. Move onto step 6.
  • Step 6: (Definitely suggested) Use a satin or gloss finish spray clear coat (I used satin finish, just because that’s what I had). You should only need one coat, but make sure to spray from all sides to get everything covered.
  • Step 7: Let dry. I left mine in the garage overnight, but they probably don’t need that long. Throw all your needles in a pretty container, and revel in your awesome creativity!

Other ideas I had included to label the side of the needle “bead” and glue something pretty on the top, like a button, or a plastic or fabric flower, or a bow… Pretty much anything you can think of!

I’m still trying to figure out what to do with my circulars and DPNs. Who has some ideas?